Wheels falling off trailers – and how to stop it happening

by | Nov 2, 2020 | Articles, Caravan/Tow Vehicle Behaviour & Suspension, General, Roll

by Collyn Rivers

Wheels Falling Off Trailers

Wheels fall off trailers, their wheel studs break or wheel nuts loosen. Trailer wheel bearings need ongoing replacement. Stub axles may fracture. Next to none of this, however, occurs with the tow vehicles. Here is why it happens, and how to prevent it.

That fastenings such as wheel nuts may be caused, not just permitted, to loosen is rarely covered in engineering training. The causes and prevention are, however, known. This referenced article by Collyn Rivers explains how, why and how to prevent it.

Wheels falling off trailers – and fastenings work loose

The thread of a screw fastening must have some side clearance to enable the nut (or stud) to be turned. Tightening, however, causes the stud to stretch slightly. This marginally decreases its diameter, thus increasing inter-thread clearance. Inter-thread friction normally prevents or limits sideways movement between the threads.  As the thread is spiral and in tension, momentarily relaxing the frictional contact may cause the fastening to ‘ratchet’ itself undone. Overtightening worsens this as it further decreases thread diameter – thereby increasing the interthread gap. Wheels fall off trailers because of this.

To see this happens, hold (by its head and pointing downwards) a large-diameter clean dry coarse-threaded bolt, with a loose nut. While stationary, the nut (restrained by minor inter-thread friction) stays where it is. If shaken from side to side, however, gravity will cause the nut to unwind. With a similar bolt and nut under tension, repetitive sideways movement above a certain force will likewise ‘ratchet’ that nut loose.

This can happen with wheel nuts or studs. As the wheels encounter bumps and pot-holes, shock loads impact the wheel studs. Unless correctly tightened or somehow restrained, the studs or nuts may work loose.

Wheels falling off trailers - and how to stop it happening - wheels falling off,wheel nuts,wheel studs,tyre pressure,tow ball,trailer wheel bearings,tow ball weight

The stub axle sheered off this tour group’s trailer on the corrugated track road to the tip of Cape York. It had no shock absorbers, nor provision for fitting them. The OKA in the distance belonged to the author. Pic: Author.

Why wheels fall of trailers – but rarely off whatever tows them

Fastenings mainly loosen where there are repeated side shocks. It also occurs where bolted assemblies bend. etc. It happens particularly with wheel studs and nuts and is usually why wheels fall off.

Far more wheels fall off travel trailers and camper trailers than ever from cars. Wrecked trailers with wheels torn off, or stub axles broken, litter mainly corrugated outback tracks. It does not, however, affect all trailers. If you inspect them you will find that almost all not just lack shock absorbers – most lack provision for fitting them.

The effect of not having shock absorbers

A wheel encountering corrugation (etc) is thrust upward. This compresses the spring. Inter-leaf friction absorbs a small part of the impact on the upward movement. Most, however, remains (as elastic energy) in that spring. Once over the bump, the now unrestrained spring jackhammers the wheel and axle downward. The wheel strikes the road with huge force. The resultant shock load (proportional to the wheels and axle’s mass and the square of their velocity) is now taken via the unfortunate wheel studs.

This issue is at its worst on corrugated roads. These typically have about 1100 plus corrugations per kilometre: 1000 km of corrugation imparts over one million hammer-like blows. All via those studs. Once the stud or nut works even slightly loose. Impact forces may then shear the studs in half. Such repeated shock loads also wreck wheel bearings. Furthermore, they may eventually cause stub axles to break.

This rarely happens with tow vehicles. All have shock absorbers, and even if badly worn most retain at least some damping effect. Much as firing an arrow into water, shock absorbers absorb and dissipate energy. They convert much of the springs released elastic energy into heat. The vehicle tyres also dissipate such energy.

wheels falling off trailers

The omission of shock absorbers on trailers (and consequent problems) is confined mostly to Australia. The above is an ultra-cheap but well-engineered Finnish garden trailer that has such large shock absorbers as standard. Pic: rvbooks.com.au.

Friction shock absorbers were fitted to cars as early as 1905. They had them despite travelling at low speed and thus incurring far lower forces. If a trailer maker says shock absorbers are not needed, buy from somewhere else.

Some trailers but rarely travel trailers have springs so stiff there’s little movement to dampen. The springs may not break but the trailer contents take a beating. Furthermore, wheel studs and stub axles are more likely to shear.

Correctly tightening wheel studs and nuts

1. Clean threads thoroughly. Ensure nuts are free to spin along the stud’s full threaded length. Discard any that do not. Never use a nut or stud that is or has been corroded. Studs and nuts need to be totally clean and dry.

2. Locate the wheel on the studs. Finger-tighten using a diagonal sequence. Give the wheel a few wriggles to allow correct location.

3. Tighten diagonally and progressively.

4. Use a torque wrench for final tightening and only to vehicle maker’s specifications. Never exceed specified tightness. That ‘more is better’ is counter-productive – it stretches the thread, thereby reducing its diameter – and hence the gap between the threads.

5. Recheck after 50 km and a further 100 km. If further re-tightening is needed, whatever is being clamped is under-engineered and bending. This occurs with U-bolt axle clamping plates on early OKAs. Any such issue needs urgent fixing by an engineer. If really seeking a belt and braces approach, apply Loctite 290 after the final bedding down. See below re how it works.

If employing a tyre fitter, insist beforehand that a torque wrench be used for final tightening to the vehicle maker’s specification (most include that in the instruction manual).

Never allow anyone to use a rattle gun for this: the risk of serious risk over-tightening is high. Ideally, have a high-quality torque wrench and insist on doing the final tightening yourself.

Insist on the above. Many mechanics and tyre fitters believe they can ‘feel’ correct tension. Extensive research shows that few can do so. Tests (conducted by Vauxhall/Bedfords Research) show variations of plus/minus 30%..

Loctite – and similar products

If there is no inter-thread gap, no side movement is possible. There is hence little likelihood of such threaded fastenings undoing. Rather than ‘glueing’ threads together, Loctite (and similar products) thus expand. They fill the gap between threads. This specifically precludes sideways movement – that enables, or causes, undoing.

The specialised Loctite 290 product is designed for fastenings that subsequent re-tightening (e.g. wheel and U-bolt nuts). It is applied after the initial re-tightening period. It is a self-wicking fluid that works its way between even horizontal threads. As the product effectively precludes nut unwinding, further torque checks are (claimed to be) unnecessary. It must, however, be reapplied after wheel changes.

This product is also used to prevent catastrophic failures. It is thus used in aircraft, and also roller coasters. It even prevents jackhammers from falling apart.

Even without Loctite, in over 500,000 km and fifty years of mostly off-bitumen driving, I have yet to have a wheel nut even loosen. Let alone fall off. And that includes twice across Africa, and a now fourteen return trips across Australia from Sydney to Broome, mainly on corrugated dirt tracks via Alice Springs. All I do is to tighten, via a torque wrench, to the amount the vehicle maker advises. And use truly high-quality shock absorbers.

Rattle guns are prone to over tighten, thereby stretching the stud. This reduces its diameter, thus increasing inter-thread spacing. This alone causes studs to crack and/or sheer off. The fastener and automobile industries emphasise that wheel nuts and studs must never be finally tightened by rattle guns (impact wrenches). They insist that such tightening may only be done via a high-quality torque wrench. This wrench must have known accuracy. It must tighten to vehicle manufacturer’s specified amounts.

Recheck (and tighten if necessary) after 50-100 km. And again after 1000 km. But many tyre fitters sadly ‘know better’. They use only rattle guns.

If you use a lubricant (most authorities recommend against it) you must reduce tightening torque by about 20%. Do not use anti-seize materials, for any but totally static applications. Their intended role is easing undoing.

Caravan Council of Australia

Here’s what the Caravan Council of Australia says about it.

‘The CCA continually receives reports of broken wheel studs, and loose wheel nuts… sometimes with the nuts unwinding completely off the studs.

It must be stressed that if a stud breaks, it is certainly no proof that the stud itself was faulty. There are a number of reasons for the problems.

‘All supplied instructions regarding wheels and wheel nuts must be precisely followed.

‘It is vital to ensure that if ‘van owners or dealers fit after-market wheels and nuts, they thoroughly check to ensure the replacement wheels and nuts are, in fact, completely suitable for the vehicle and axles.

Possible Reasons for Broken Wheel Studs, or Loose – and Lost – Nuts:

  • The pitch circle of the studs in the (imperial) hub not exactly the same as that of the holes in some (metric) wheels, such that all studs bend when the nuts are tightened
  • The angle of the taper on the nuts not the same as the angle of taper in the wheels
  • Low-Grade steel studs being used
  • The hole in the wheel centre not compatible with the spigot diameter of the hub
  • The serrated studs not “fully driven home” when pressed into the hubs, such that they gradually “give a little”, thus causing the nuts to become loose
  • Rattle-guns – set at unknown high-torque levels – used to tighten wheel nuts (rather than just undo them), causing the studs to stretch, and thus become weakened
  • Nuts being tightened in a circular pattern in one action, rather than in a criss-cross pattern, using two or three (increasing) torques
  • Wheel centres being highly dished, thus acting as a large spring-washer that gradually loses its tension and causes the nuts to loosen.

Clearly, all nuts must be tightened to the correct torque, and in the correct pattern, in strict accordance with the instructions provided by the wheel or chassis manufacturer.

It is strongly recommended that pencil lines are made on one face of each nut – with a mating line on the wheel – so that a quick visual inspection can detect any loosening of a nut.  Clip-on plastic “indicators” – fitted to each nut, with their adjacent “arrow-heads” aligned – provide an even-quicker warning of any nut loosening.

Continual vibrations – and occasional heavy impacts – from road surfaces, inevitably have an adverse effect on the wheel assemblies.

This is severely aggravated if the tyre pressures – and the spring rates – are too high for the actual wheel-loading.

Stresses on the wheel assemblies are further increased if shock-absorbers (dampers) are not fitted.

Leaf-springs do provide some damping of vibrations, but unfortunately, it is mainly on the “bump” (up-wards) movement of the wheel, rather than on the “rebound” (down-wards) movement of the wheel… where it would be far more beneficial.’

Wheels falling off trailers – further information

Our published books are written much like this article. They are technically competent but in plain English. They include the Caravan & Motorhome Book, the Caravan & Motorhome Electrics and the Camper Trailer Book. Solar is covered in Solar That Really Works – for cabins and RVs. Solar Success is for homes and properties. For information about the author please Click on Bio.

References

Designing with Threaded Fasteners, Havil G.S, Mech. Eng., Vol 105, No 10, Oct 1983.

Medium/Heavy Truck Wheel Separations, National Transportation Safety Board, Report No. PB92-917004, NTSB/SIR-92/04, Sept 1992.

Myths That Must Be Shattered, Automotive Industries, (April, 1982) p.43.

Design Handbook, Loctite Corporation, (1968) 160 pages.

A Logical Approach to Secure Bolting, Havil, G.S. Soc. of Manufacturing Engineers Ref: AD80-329.

Fastening and Joining, Machine Design, Issue 1967, Vol 14, Penton Publishing.

The Use and Misuse of Six Billion Bolts a Year, Kerely J. J., NASA Goddard Space Centre. Delivered, 35th meeting of the Mechanical Failures Prevention Group, NBS.

Collyn Rivers is a semi-retired automobile research engineer.  He is the author of seven books, five of which are about making RVs and solar work optimally.

Caravan and Motorhome Electrics

The essential handbook for anyone with an RV of any kind.  Everything you need to know to make the electrics in your rig work for you.

Cover of Caravan and Motorhome Books by Collyn Rivers

eBook versions

Paperback version

The book retailers set their own prices which can vary substantially. We'll aim to keep a selection of the better prices above.

Any bookshop, whether online or bricks and mortar, can order copies of Caravan & Motorhome Electrics.  Just ask.
ISBN: 978-0-6483190-8-5

Solar Success

Whether you’re building a new home or adding solar to an existing structure, this is the one book you can’t afford to be without.

eBook versions

Paperback version

Any bookshop, whether online or bricks and mortar, can order copies of Solar Success.  Just ask.
ISBN: 978-0-6487945-4-7

Why Caravans Roll Over
and how to prevent it

Explains in detail every aspect of tow vehicle and travel trailer stability. This is what you need to know to be safe on or off the road.

eBook versions

Paperback version

The book retailers set their own prices which can vary substantially. We'll aim to keep a selection of the better prices above.

Any bookshop, whether online or bricks and mortar, can order copies of Why Caravans Roll Over.  Just ask.
ISBN: 978-0-6483190-6-1

Solar That Really Works!

Solar that Really Works! covers the design, installation and use of solar in cabins, camper trailers, travel trailers, fifth wheelers, campervans and motor homes.

eBook versions

Paperback version

The book retailers set their own prices which can vary substantially. We'll aim to keep a selection of the better prices above.

Any bookshop, whether online or bricks and mortar, can order copies of Solar That Really Works!  Just ask.
ISBN: 978-0-6483190-3-0

The Caravan & Motorhome Book

The Caravan & Motorhome Book covers every conceivable aspect of campervan and motorhome usage. If you own a camper van or motor home, you'll want this book.

eBook versions

Paperback version

The book retailers set their own prices which can vary substantially. We'll aim to keep a selection of the better prices above.

Any bookshop, whether online or bricks and mortar, can order copies of The Caravan & Motorhome Book. Just ask.
ISBN: 978-0-6483190-5-4.

Most Viewed Articles

Sorry. No data so far.

Caravan and Motorhome Electrics

The essential handbook for anyone with an RV of any kind.  Everything you need to know to make the electrics in your rig work for you.

Cover of Caravan and Motorhome Books by Collyn Rivers

eBook versions

Paperback version

The book retailers set their own prices which can vary substantially. We'll aim to keep a selection of the better prices above.

Any bookshop, whether online or bricks and mortar, can order copies of Caravan & Motorhome Electrics.  Just ask.
ISBN: 978-0-6483190-8-5

Solar Success

Whether you’re building a new home or adding solar to an existing structure, this is the one book you can’t afford to be without.

eBook versions

Paperback version

Any bookshop, whether online or bricks and mortar, can order copies of Solar Success.  Just ask.
ISBN: 978-0-6487945-4-7

The Caravan & Motorhome Book

The Caravan & Motorhome Book covers every conceivable aspect of campervan and motorhome usage. If you own a camper van or motor home, you'll want this book.

eBook versions

Paperback version

The book retailers set their own prices which can vary substantially. We'll aim to keep a selection of the better prices above.

Any bookshop, whether online or bricks and mortar, can order copies of The Caravan & Motorhome Book. Just ask.
ISBN: 978-0-6483190-5-4.

Solar That Really Works!

Solar that Really Works! covers the design, installation and use of solar in cabins, camper trailers, travel trailers, fifth wheelers, campervans and motor homes.

eBook versions

Paperback version

The book retailers set their own prices which can vary substantially. We'll aim to keep a selection of the better prices above.

Any bookshop, whether online or bricks and mortar, can order copies of Solar That Really Works!  Just ask.
ISBN: 978-0-6483190-3-0

Why Caravans Roll Over
and how to prevent it

Explains in detail every aspect of tow vehicle and travel trailer stability. This is what you need to know to be safe on or off the road.

eBook versions

Paperback version

The book retailers set their own prices which can vary substantially. We'll aim to keep a selection of the better prices above.

Any bookshop, whether online or bricks and mortar, can order copies of Why Caravans Roll Over.  Just ask.
ISBN: 978-0-6483190-6-1